[linux-help] Re: cd burner

[Craig Terhune <cterhune@xxxxxxxxxxx>]

I added the line /sbin/modprobe ide-scsi and got this in my boot message:
but the sdrecord -scanbus output was the same?
<4>hda: WDC AC33100H, ATA DISK drive
<4>hdb: WDC AC2540H, ATA DISK drive
<4>hdc: ATAPI CDROM, ATAPI CDROM drive
<4>hdd: Memorex CRW-1622, ATAPI CDROM drive
<4>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
<4>ide1 at 0x170-0x177,0x376 on irq 15
<6>hda: WDC AC33100H, 3020MB w/128kB Cache, CHS=3D767/128/63
<6>hdb: WDC AC2540H, 515MB w/128kB Cache, CHS=3D524/32/63
<4>hdc: ATAPI 24X CD-ROM drive, 128kB Cache
<6>Uniform CDROM driver Revision: 2.56
<6>Floppy drive(s): fd0 is 1.44M
<6>FDC 0 is a post-1991 82077
<6>LVM version 0.8e  by Heinz Mauelshagen  (4/1/2000)
<4>lvm -- Driver successfully initialized
<4>md driver 0.36.6 MAX_MD_DEV=3D4, MAX_REAL=3D8
<4>linear personality registered
<4>raid0 personality registered
<4>raid1 personality registered
<4>raid5 personality registered
<4>scsi : 0 hosts.
<4>scsi : detected total.
<4>Partition check:
<4> hda: hda1 hda2 hda3 hda4
<4> hdb: hdb1
<4>VFS: Mounted root (ext2 filesystem) readonly.
<4>Freeing unused kernel memory: 64k freed
<6>Adding Swap: 129020k swap-space (priority -1)
<4>scsi0 : SCSI host adapter emulation for IDE ATAPI devices
<4>scsi : 1 host.
<4>  Vendor: Memorex   Model: CRW-1622          Rev: D4.0
<4>  Type:   CD-ROM                             ANSI SCSI revision: 02
<4>Detected scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
<4>  Vendor: Memorex   Model: CRW-1622          Rev: D4.0
<4>  Type:   CD-ROM                             ANSI SCSI revision: 02
<4>Detected scsi CD-ROM sr1 at scsi0, channel 0, id 0, lun 1
<4>  Vendor: Memorex   Model: CRW-1622          Rev: D4.0
<4>  Type:   CD-ROM                             ANSI SCSI revision: 02
<4>Detected scsi CD-ROM sr2 at scsi0, channel 0, id 0, lun 2
<4>  Vendor: Memorex   Model: CRW-1622          Rev: D4.0
<4>  Type:   CD-ROM                             ANSI SCSI revision: 02
<4>Detected scsi CD-ROM sr3 at scsi0, channel 0, id 0, lun 3
<4>  Vendor: Memorex   Model: CRW-1622          Rev: D4.0
<4>  Type:   CD-ROM                             ANSI SCSI revision: 02
<4>Detected scsi CD-ROM sr4 at scsi0, channel 0, id 0, lun 4
<4>  Vendor: Memorex   Model: CRW-1622          Rev: D4.0
<4>  Type:   CD-ROM                             ANSI SCSI revision: 02
<4>Detected scsi CD-ROM sr5 at scsi0, channel 0, id 0, lun 5
<4>  Vendor: Memorex   Model: CRW-1622          Rev: D4.0
<4>  Type:   CD-ROM                             ANSI SCSI revision: 02
<4>Detected scsi CD-ROM sr6 at scsi0, channel 0, id 0, lun 6
<4>  Vendor: Memorex   Model: CRW-1622          Rev: D4.0
<4>  Type:   CD-ROM                             ANSI SCSI revision: 02
<4>Detected scsi CD-ROM sr7 at scsi0, channel 0, id 0, lun 7
<4>sr0: scsi3-mmc drive: 6x/6x writer cd/rw xa/form2 cdda tray
<4>sr1: scsi3-mmc drive: 6x/6x writer cd/rw xa/form2 cdda tray
<4>sr2: scsi3-mmc drive: 6x/6x writer cd/rw xa/form2 cdda tray
<4>sr3: scsi3-mmc drive: 6x/6x writer cd/rw xa/form2 cdda tray
<4>sr4: scsi3-mmc drive: 6x/6x writer cd/rw xa/form2 cdda tray
<4>sr5: scsi3-mmc drive: 6x/6x writer cd/rw xa/form2 cdda tray
<4>sr6: scsi3-mmc drive: 6x/6x writer cd/rw xa/form2 cdda tray
<4>sr7: scsi3-mmc drive: 6x/6x writer cd/rw xa/form2 cdda tray
On Sun, 17 Dec 2000, you wrote:
> =3D46rom the looks of the output I would say no. Where do I go from her=
e?
>=20
>=20
> root@hal:/home/cterhune > cdrecord -scanbus
> Cdrecord 1.8 (i686-pc-linux-gnu) Copyright (C) 1995-2000 J=3DF6rg Schil=
ling
> cdrecord: Permission denied. Cannot open '/dev/sg0'. Cannot open SCSI d=
ri=3D
> ver.
> cdrecord: For possible targets try 'cdrecord -scanbus'. Make sure you a=
re=3D
>  root.
> root@hal:/home/cterhune >  =3D20
>=20
> =3D20
> On Sun, 17 Dec 2000, you wrote:
> > Did you set up your cd writer to be used via scsi-emulation?
> > try entering (as root)
> >=3D20
> > cdrecord -scanbus
> >=3D20
> > Is your writer listed?
> >=3D20
> >=3D20
> > On Sunday 17 December 2000 13:04, you wrote:
> > > How is the burner listed in the fstab? I have installed mkisofs and=
 c=3D
> drec=3D3D
> > > ord,
> > > so I can use other front end tools., like they say to. But as with =
ko=3D
> ncd =3D3D
> > > it
> > > list the atapi cd-rom but doesn't show a writer. Any ideas
> > > --  WALL'S A'LAMODE
> > > Wall flavors for every palette.
> > > http://walls.homeip.net
> > >
> > > -- This is the linux-help@xxxxxxxxx list.  To unsubscribe,
> > > visit http://tmp2.complete.org/cgi-bin/listargate-aclug.cgi
> >=3D20
> > -- This is the linux-help@xxxxxxxxx list.  To unsubscribe,
> > visit http://tmp2.complete.org/cgi-bin/listargate-aclug.cgi
> --=3D20
> WALL'S A'LAMODE
> Wall flavors for every palette.
> http://walls.homeip.net
>=20
> -- This is the linux-help@xxxxxxxxx list.  To unsubscribe,
> visit http://tmp2.complete.org/cgi-bin/listargate-aclug.cgi
--=20
WALL'S A'LAMODE
Wall flavors for every palette.
http://walls.homeip.net

-- This is the linux-help@xxxxxxxxx list.  To unsubscribe,
visit http://tmp2.complete.org/cgi-bin/listargate-aclug.cgi